Collection
Cables & Connectors
Cables & Connectors
Showing 17 products
PV Connector DC MC4 6mm2 1500V
PV Connector DC MC4 6mm2 1500V
PV Dual Core Solar cable 1500V 6mm2
Designed for photovoltaic installations, this dual-core 6mm² cable delivers efficient and safe DC transmission from solar panels to inverters, charge controllers, and batteries. The 6mm² cross-sectional area provides high current carrying capacity with minimal power loss, keeping your system running at peak efficiency. Built tough with dual-wall XLPE insulation that is electron-beam cross-linked, offering exceptional resistance to UV radiation, water, ozone, fluids, salt, and general weathering. Halogen-free and low-smoke construction meets modern environmental standards, with a service life of over 25 years. Rated for operation from -40°C to +90°C with a current rating of up to 50A depending on installation conditions. Despite its robust build, the cable remains flexible and easy to route, ideal for both professional installers and DIY solar setups. Suitable for off-grid, hybrid, and grid-tied systems.
PV DC Isolation Switch MC4 - SISO-40 1000V 32A
PV DC Isolator MC4 Features UV Resistant IP66 Enclosure Extremely Short Power Shut Off Time Of Approx.2ms Lid Only Removable In "off" Position Earth Terminal 1EC60947-3,AS/NZS60947.3: 2015 DC-PV1 DC-PV2 DC-21B 10A To 32A UP To DC1000V Easy To Install MC4 Connector
PV DC Isolation Switch SISI-40 1000V 32A
PV DC Isolator Features UV Resistant IP66 Enclosure Extremely Short Power Shut Off Time Of Approx.2ms Lid Only Removable In "off" Position Earth Terminal 1EC60947-3,AS/NZS60947.3: 2015 DC-PV1 DC-PV2 DC-21B 10A To 32A UP To DC1000V Easy To Install 4 -16MM2 Cable
ABS Solar Panel Roof Mount 6 Piece
Heavy-Duty ABS Caravan Solar Panel Mounting Kit Securely mount your fixed solar panel to your caravan, motorhome, or boat with this heavy-duty ABS mounting kit. The design creates an air gap between the solar panel and the mounting surface, improving ventilation and cooling. This helps maintain optimal panel efficiency, even in hot conditions. Installation Ensure the mounting surface is clean. Drill through the ABS brackets into the solar panel’s aluminium frame, then fasten with screws. Apply adhesive (e.g. Sikaflex) to the brackets, then glue the panel securely to your roof or deck. For maximum strength, we recommend using both adhesive and screws. ⚠️ Always confirm that the adhesive is suitable for your specific roof material before installation. Kit Includes 4 x Corner mounting brackets 2 x 180mm side mounting brackets
PV Dual Core Solar cable 1500V 4mm2
Designed for photovoltaic installations, this dual-core 6mm² cable delivers efficient and safe DC transmission from solar panels to inverters, charge controllers, and batteries. The 6mm² cross-sectional area provides high current carrying capacity with minimal power loss, keeping your system running at peak efficiency. Built tough with dual-wall XLPE insulation that is electron-beam cross-linked, offering exceptional resistance to UV radiation, water, ozone, fluids, salt, and general weathering. Halogen-free and low-smoke construction meets modern environmental standards, with a service life of over 25 years. Rated for operation from -40°C to +90°C with a current rating of up to 50A depending on installation conditions. Despite its robust build, the cable remains flexible and easy to route, ideal for both professional installers and DIY solar setups. Suitable for off-grid, hybrid, and grid-tied systems.
MC4 Y Branch Connectors Pair - 2 in 1 Solar Panel Cable Connector
This MC4 2-way connector lets you parallel-connect two solar panel strings (or combine two panel outputs) quickly and safely using standard MC4-compatible plugs. It provides a weather-resistant, UV-stable connection for tidy installs and reliable performance in outdoor solar arrays—ideal for RV, marine, off-grid, and residential PV systems. Features Creates a 2-way parallel branch using MC4-compatible connections. Weather-resistant housing for outdoor use (rating depends on model). UV-resistant materials for long service life. Quick plug-and-play connection—no special tools required. Helps keep wiring neat and reduces the need for junction boxes (in some layouts). Specifications Rated Voltage: 1000V (TUV) 600V (UL) Rated Current: 50A TEst Voltage: 6KV (TUV50HZ, 1min) IP Rating: IP67 Temp Range: -40℃ ~+85℃ Contact Resistance: <0.5mΩ Typical applications Parallel PV string combining, adding extra panels to an existing string, RV/van solar, marine solar, off-grid arrays, and rooftop PV expansions.
ABS Solar Panel Roof Mount 4 Piece
Securely mount your fixed solar panel to your caravan, motorhome, or boat with this heavy-duty ABS mounting kit. The design creates an air gap between the solar panel and the mounting surface, improving ventilation and cooling. This helps maintain optimal panel efficiency, even in hot conditions. Installation Ensure the mounting surface is clean. Drill through the ABS brackets into the solar panel’s aluminium frame, then fasten with screws. Apply adhesive (e.g. Sikaflex) to the brackets, then glue the panel securely to your roof or deck. For maximum strength, we recommend using both adhesive and screws. ⚠️ Always confirm that the adhesive is suitable for your specific roof material before installation. Kit Includes 4 x Corner mounting brackets
LONGi Mono 440W Solar Panel
Please note that all solar panels are classified as oversize. When ordering please use the direct transfer option and we will provide a custom freight quote. The latest LONGi HPBC solar panels are engineered to excel in New Zealand's winter weather, outperforming older models with bifacial Topcon, type n model. Leveraging advanced technology, these new panels deliver significantly higher power generation efficiency during winter and rainy conditions. Featuring an impressive output of 440 watts, the LONGi high-performance solar module is AU/NZ certified. This latest version offers superior quality, enhanced efficiency, extended lifespan, and reduced degradation. 25-year Warranty for Materials and Processing 25-year Warranty for Extra Linear Power Output 23% Max Module Efficiency Mechanical Parameters Cell Orientation: 108 (6X 18) Junction Box: IP68 Glass: Single glass, 3.2mm coated tempered glass Frame: Anodized aluminium alloy frame Weight: 20.8kg Dimension: 1722x1134x30mm Electrical Characteristics Module Type: LR5-54HTB-440M Testing Condition: STC Maximum Power (Pmax/W): 440 Open Circuit Voltage (Voc/V): 39.83 Short Circuit Current (lsc/A): 14.15 Voltage at Maximum Power 0/mp/V): 33.56 Current at Maximum Power (Imp/A): 13.12 Module Efficiency(%) : 22.5
PV DC Isolator Din / 32A / 4P / 1000V
DC Isolator DC300V-1000V UV resistance and VO flame retardant material Contact Silver Plating, silver layer thickness up to the industry's highest standards Arcing Time in 3 ms No Polarity Lockable at OFF position IEC/EN60947.3 standard and AS 60947.3 Provide 5-year warranty product guarantee
Suntree 2 in - 2 out PV Combiner box
Suntree SHLX-PV2/2 DC Combiner Box — 1000V, 2 Strings In / 2 Out A compact, factory-wired DC combiner for single-string solar arrays where you still want proper overcurrent, isolation and surge protection between the panels and the inverter or charge controller. Everything's already wired at the factory, so installation is a matter of mounting the box, landing your PV positive and negative in, and running the output through to your MPPT controller. No internal assembly, no loose components, no guesswork. Inside you get double-pole fusing (one 1100V SRD-30 fuse on each pole, rated 20A), a 2-pole 1000V DC MCB rated 32A for load-break isolation, and a Type 2 DC surge protective device rated 20–40kA to clamp lightning-induced transients before they reach your inverter. That combination covers the three things that actually kill DC-side gear: overcurrent, arcing during disconnection, and surge. The IP65 enclosure is rated for outdoor mounting, so it can live on the array frame, a pole, or an exterior wall without needing its own weatherproof housing. Compact footprint makes it a good fit for tiny homes, cabins, sheds, campervan-scale ground arrays and any small off-grid setup. Specifications Model SHLX-PV2/2 Configuration 2 strings in, 2 strings out Max system voltage 1000V DC DC fuse SRD-30, 1P, 1100V, 20A (×2) DC breaker SL7N-63, 2P, 1000V, 32A Surge protection SUP2H-PV, 2P, 1000V, Type 2, 20–40kA Ingress protection IP65 Mounting Indoor or outdoor Wiring Pre-wired from factory
VE.Can. to CAN-bus BMS type B Cable 1.8M
Sogen Energy CAN Bus BMS Communication Cable - RJ45 Type 2 1.8m or 5m Getting your battery talking to your inverter or GX device is one of those things that looks simple but causes endless headaches when the cable isn't wired right. The Sogen CAN Bus cable takes care of that — purpose-built for connecting CAN-bus enabled LiFePO4 batteries to compatible inverters and GX monitoring devices, with CAN-H and CAN-L on pins 7 and 8 respectively. Compatible with Victron GX devices (VE.Can and BMS-Can ports), and any inverter or BMS device using the standard Type 2 CAN pin configuration. Available in 1.8m for tidy cabinet installs and 5m where the battery and inverter aren't sitting right next to each other. Both ends are clearly labelled so there's no guessing which end goes where. Supplied by Sogen Energy and verified compatible with SOK LiFePO4 batteries straight out of the box. No crimping, no fiddling — just plug in and configure.
IWS-2546S Solar panel crimping tool for 2.5/4/6mm2
IWISS IWS4 Solar Crimping Tool If you're working with solar connectors, do yourself a favour and get a proper crimping tool. We've been using the IWISS IWS4 and honestly it's the best we've come across — solid hardened steel construction, high-precision ratchet mechanism, and an ergonomic handle that won't destroy your hand after an hour on the job. It crimps IWS4 male and female solar contacts perfectly every time, covering 2.5, 4, and 6mm² cable. Once you've used a quality crimper, you'll never go back to the cheap ones.
Suntree 3-1 Combiner box
Suntree SHLX-PV3/1 DC Combiner Box — 500V, 3 Strings In / 1 Out A compact, factory-wired DC combiner for single-string solar arrays where you still want proper overcurrent, isolation and surge protection between the panels and the inverter or charge controller. Everything's already wired at the factory, so installation is a matter of mounting the box, landing your PV positive and negative in, and running the output through to your MPPT controller. No internal assembly, no loose components, no guesswork. Inside you get double-pole fusing (one 1100V SRD-30 fuse on each pole, rated 20A), a 2-pole 1000V DC MCB rated 32A for load-break isolation, and a Type 2 DC surge protective device rated 20–40kA to clamp lightning-induced transients before they reach your inverter. That combination covers the three things that actually kill DC-side gear: overcurrent, arcing during disconnection, and surge. The IP65 enclosure is rated for outdoor mounting, so it can live on the array frame, a pole, or an exterior wall without needing its own weatherproof housing. Compact footprint makes it a good fit for tiny homes, cabins, sheds, campervan-scale ground arrays and any small off-grid setup. Specifications Model SHLX-PV3/1 Configuration 3 strings in, 1 string out Max system voltage 1000V DC DC fuse SRD-30, 1P, 1100V, 20A (×2) DC breaker SL7N-63, 2P, 1000V, 32A Surge protection SUP2H-PV, 2P, 1000V, Type 2, 20–40kA Ingress protection IP65 Mounting Indoor or outdoor Wiring Pre-wired from factory
Suntree 2-1 Combiner box
Suntree SHLX-PV2/1 DC Combiner Box — 500V, 2 Strings In / 1 Out A compact, factory-wired DC combiner for single-string solar arrays where you still want proper overcurrent, isolation and surge protection between the panels and the inverter or charge controller. Everything's already wired at the factory, so installation is a matter of mounting the box, landing your PV positive and negative in, and running the output through to your inverter. No internal assembly, no loose components, no guesswork. Inside you get double-pole fusing (one 1100V SRD-30 fuse on each pole, rated 20A), a 2-pole 500V DC MCB rated 32A for load-break isolation, and a Type 2 DC surge protective device rated 20–40kA to clamp lightning-induced transients before they reach your inverter. That combination covers the three things that actually kill DC-side gear: overcurrent, arcing during disconnection, and surge. The IP65 enclosure is rated for outdoor mounting, so it can live on the array frame, a pole, or an exterior wall without needing its own weatherproof housing. Compact footprint makes it a good fit for tiny homes, cabins, sheds, campervan-scale ground arrays and any small off-grid setup. Specifications Model SHLX-PV2/1 Configuration 2 strings in, 1 string out Max system voltage 500V DC DC fuse SRD-30, 1P, 1100V, 20A (×2) DC breaker SL7N-63, 2P, 1000V, 32A Surge protection SUP2H-PV, 2P, 1000V, Type 2, 20–40kA Ingress protection IP65 Mounting Indoor or outdoor Wiring Pre-wired from factory
Suntree 1-1 Combiner box
Suntree SHLX-PV1/1 DC Combiner Box — 500V, 1 String In / 1 Out A compact, factory-wired DC combiner for single-string solar arrays where you still want proper overcurrent, isolation and surge protection between the panels and the inverter or charge controller. Everything's already wired at the factory, so installation is a matter of mounting the box, landing your PV positive and negative in, and running the output through to your inverter. No internal assembly, no loose components, no guesswork. Inside you get double-pole fusing (one 1100V SRD-30 fuse on each pole, rated 6–30A), a 2-pole 500V DC MCB rated 16–63A for load-break isolation, and a Type 2 DC surge protective device rated 20–40kA to clamp lightning-induced transients before they reach your inverter. That combination covers the three things that actually kill DC-side gear: overcurrent, arcing during disconnection, and surge. The IP65 enclosure is rated for outdoor mounting, so it can live on the array frame, a pole, or an exterior wall without needing its own weatherproof housing. Compact footprint makes it a good fit for tiny homes, cabins, sheds, campervan-scale ground arrays and any small off-grid setup. Specifications Model SHLX-PV1/1 Configuration 1 string in, 1 string out Max system voltage 500V DC DC fuse SRD-30, 1P, 1100V, 20A (×2) DC breaker SL7N-63, 2P, 500V, 32A Surge protection SUP2H-PV, 2P, 500V, Type 2, 20–40kA Ingress protection IP65 Mounting Indoor or outdoor Wiring Pre-wired from factory
Solar Panel Dual Roof Entry
This twin-entry solar cable gland provides a clean, reliable way to route two solar cables through the roof of a marine or mobile installation. It supports common solar cable sizes of 2.5 mm², 4 mm² and 6 mm², making it well suited to boats, caravans and RVs. The moulded housing incorporates an internal sealing channel on the underside, allowing sealant to be contained where it’s needed. This design improves weather resistance and delivers a tidier finish compared with flat-base cable glands, where sealant often spreads beyond the edges. Key specifications: • IP68 ingress protection for long-term outdoor exposure • CE compliant • Compatible with cables measuring 5–9 mm in outer diameter • Tough ABS construction for UV and impact resistance To install, drill a cable access hole beneath the gland and bond it in place using a marine-grade adhesive sealant such as Sikaflex 252 to ensure a watertight seal.